$600 · NEW-CREALITY ENDER 5 PLUS 3D PRINTER

Please note that this is an Ender 5 Plus, not the smaller Ender 5 and Ender 5 Pro. Here are the key features of the Creality Ender 5 Plus 3D Printer: • Large build volume: 350 x 350 x 400 mm • Automatic bed leveling • Filament detection • Easy to build - start printing fast 3D PRINT LARGE PARTS The Creality Ender 5 Plus has a large build volume, allowing you to print big parts, or a lot of smaller parts all at once. • Build Volume: 350 x 350 x 400mm • Unlimited freedom to create • Print large parts beautifully BUILT-IN FILAMENT DETECTION SENSOR The Creality Ender 5 Plus is equipped with a Filament Detection Sensor that will immediately pause your print when it runs into issues, like if your filament runs out or you experience a power failure. • Print with confidence and peace of mind • Save your print when power outages occur • Pauses print when filament runs out or breaks STURDY ALUMINUM RAILS & DOUBLE AXIS CONTROL SYSTEM The Creality Ender 5 Plus has been designed from the ground up to improve the stability and printer performance of the entire machine. • Reinforced aluminum rails • Double Axis Control System reduces vibrations for cleaner prints • Box-shaped design for improved stability TOOL/ACCESSORY LIST: • Creality Upgraded Ender 5 Plus Silent Motherboard with TMC2208 Driver • 4 new 250gr filament rolls • PEI Powder Coated Steel Sheet Flexible Build Plate • Original glass build plate • Needle nozzle cleaners • 2-0.2,03,05,06.08mm hardened steel nozzles • 4-04mm hardened steel nozzles • 5-04mm brass nozzles • 5 Silicon hotend shields • 1-Spare new CR Touch probe • 1-All metal extruder and hotend with .04mm hardened steel nozzle • 1- Dual filament extruder and hotend with .04mm brass nozzle • 4 Red Z Axis Knurled Couplers • 2 16mm Z Axis brass couplers • 2 16mm Z Axis brass couplers • 10-meter D-RGB LED strip • Complete set of replacement cables for stepper motors and end stops • Spare X Axis carriage (not shown) to modify for mounting Sprite extruder • M12 4mm Inductive Proximity Switch bed leveling Sensor upgrade • Wrench and screwdriver • Storage card • 2 Allen wrenches This printer is in "like new" condition and has not even had any filament run through it. This is due to the printer arriving the and I was unable to get the auto bed leveling to work. The initial hic-up was the beds Z Axis operating in the reverse direction. After some time, I was able to figure that problem out and attempt to run the auto level program. This time everything worked fine, and the bed auto leveled, but when the bed raised to its Z Axis home position to start a 3d print, the bed crashed into the hotend carriage and the CR Touch probe, bending the tip. After several attempts to get it to work correctly the probes contact shaft finally broke off. I ordered two new one, and after a few weeks it finally showed up, but the problem remains. Installed the new CR Touch, but the problem remained. The project I had purchased the Ender 5 Plus for was completed on one of my smaller printers and I now no longer need the Ender 5 Plus. I am selling this printer ‘as is’ which is in brand new condition (no box) but with the Z Axis levelling and home stop problem remaining for you to trouble shot as I have given up due to limited experience. If you are an experienced 3-D printer person and familiar with g-code, or someone that wants to go through some YouTube how-to videos and give it a whirl, you should have no problem getting this printer up and running as I have added most of the replacement items you would need to get it bed leveling like a pro. You could also simply level the bed manually and skipped the auto leveling all together. I simply just ran out of time due to the time crunch created by the project needing to be completed by a certain date and need to make room. My price for the printer and accessories was well over $800, your price $600 all included. The printer and all the accessories and Creality's Fireproof Enclosure for printing exotic filaments are brand new and have never been used and are in new-unused condition. Price: $600 Firm. Available: Creality Sprite Direct Drive Extruder Kit with spare hotend. Can be water cooled: $120 Firm **Located in Duncan. Free delivery available for the Duncan Cowichan Valley area. Can deliver to Nanaimo or Victoria for $20. I do not accept any form of cheque. Sorry scammers. Accept cash and e-transfers.